GET http://10.10.2.1/api/status Response 200
This interface is accessible only from within your local area network (LAN). To reach the mixer, type http://10.10.2.1/mixer.html directly into the address bar of any browser connected to the same private network. (Note: the "www" prefix is typically omitted for IP-based addresses.)
For the most reliable connection with the lowest latency, a direct wired Ethernet connection is strongly recommended. This method also involves configuring your computer's network adapter manually. In your mixer's settings menu, navigate to the Network tab and enter the configuration panel. The default login credentials for this administrative area are "admin" for both the username and password. From there, under LAN Configuration, ensure the Ethernet port is enabled, select "Manual mode," and then enter the and Subnet Mask: 255.255.255.0 . Simultaneously, you must configure your computer's network adapter. On a Windows PC, navigate to the Network & Sharing Center, find your Ethernet adapter's properties, select Internet Protocol Version 4 (TCP/IPv4), and set your computer's IP address to 10.10.2.5 (or any address in the 10.10.2.x range except .1). On a Mac, go to System Preferences > Network, select the Ethernet connection, set "Configure IPv4" to "Manually," and enter the same parameters: IP Address 10.10.2.5, Subnet Mask 255.255.255.0, and Router 10.10.2.1. Once these settings are saved, you can open your browser and navigate to 10.10.2.1 to access the full mixing interface.
While the mixer's internal Wi-Fi is convenient, its range and stability can be improved by integrating a third-party wireless router. This requires a few configuration steps on both devices. First, log into your external router's administration interface. For many routers, this is done by entering the router's IP address (often 192.168.1.1 ) in your browser. Find the router's local IP address, which is often referred to as the "Gateway". Ensure the router's DHCP server is enabled and note the range of IP addresses it hands out to connected devices, as you will need to assign a static IP address to your mixer that falls outside of this range to prevent conflicts. For instance, if your router's DHCP range is 192.168.1.100 to 192.168.1.150 , you could safely assign your mixer an address like 192.168.1.200 . With this information, connect to your mixer's hotspot, go to the network configuration area, and change its LAN IP address from the default 10.10.2.1 to the chosen static address on your router's network, such as 192.168.1.200 . After saving and rebooting, the mixer will be a permanent, accessible device on your external network, allowing any device connected to your router to find and control it via that new IP address. www.10.10.2.1 mixer.html
The IP address 10.10.2.1 serves as the default wired LAN access point for Soundcraft Ui Series digital mixers (Ui12, Ui16, Ui24R), allowing control via any browser. To connect, users must configure a static IP on their device to match the network range, bypassing the need for dedicated apps. Troubleshooting typically involves setting the wired connection and, if necessary, using default admin credentials for network adjustments. For detailed troubleshooting, see the Sweetwater troubleshooting guide . Network Requirements for the Ui Series Mixers
Get Started! Ui Series - Soundcraft - Professional Audio Mixers | English
The most prominent use of 10.10.2.1 is as the default IP address for the (e.g., Ui12, Ui16, Ui24R). In this role: GET http://10
This public link is valid for 7 days and shares a thread, including any personal information you added. This link or copies made by others cannot be deleted. If you share with third parties, their policies apply. Can’t copy the link right now. Try again later. Soundcraft Ui Mixers | Getting Connected to the Ui
The address 10.10.2.1/mixer.html acts as the browser-based control panel for Soundcraft Ui Series digital mixers, allowing local, app-free control via HTML5-compliant devices. By connecting to the mixer's internal Wi-Fi and entering this address, users gain access to comprehensive audio processing, including Lexicon effects, EQ, and input/output routing. For detailed setup information, visit Soundcraft . Share public link
The interface should be built with HTML5 and CSS3 for structure and styling. JavaScript (potentially with frameworks like React or Angular) can be used to add interactivity, especially for real-time updates and dynamic changes. From there, under LAN Configuration, ensure the Ethernet
Beyond the basic interface, the Ui series offers deep integration and powerful features:
This public link is valid for 7 days and shares a thread, including any personal information you added. This link or copies made by others cannot be deleted. If you share with third parties, their policies apply. Can’t copy the link right now. Try again later. IP: 10.10.2.1 Login Page Username Password - IPSHU